Calculation of I(0+), di/dt(0+), d2I/dt2(0+) in Circuits Involving both Capacitor and Inductor MCQ’s

Electronics & Communication Engineering Network Theory

This set of Network Theory Multiple Choice Questions & Answers (MCQs) focuses on “Calculation of I(0+), di/dt(0+), d2I/dt2(0+) in Circuits Involving both Capacitor and Inductor”.

1. A coil of inductance 10 H, resistance 40 Ω is connected as shown in figure. The switch S connected with point 1 for a very long time, is moved to point 2 at t=0. For the value of R obtained, the time taken for 95 % of the stored energy dissipated is ________

tough-network-theory-questions-answers-q1

a) 0.10 s
b) 0.15 s
c) 0.50 s
d) 1.0 s

2. In the circuit shown below steady state is obtained before the switch closes at t = 0. The switch is closed for 1.5 s and is then opened. At t = 1 s, V (t) will be?

tough-network-theory-questions-answers-q3

a) – 3.24 V
b) 1.97 V
c) 5.03 V
d) 13.24 V

3. A coil of inductance 10 H, resistance 40 Ω is connected as shown in the figure. The switch S connected with point 1 for a very long time, is moved to point 2 at t=0. If, at t=0+, the voltage across the coil is 120 V, the value of the resistance R is __________

tough-network-theory-questions-answers-q1

a) Zero
b) 20 Ω
c) 40 Ω
d) 60 Ω

4. The circuit shown below is at steady state before the switch closes at t=0. The switch is closed for 1.5 s and is then opened. At t = 2 s, V (t) will be?

tough-network-theory-questions-answers-q3

a) 5.12 V
b) 6.43 V
c) 8.57 V
d) 9.88 V

5. In the circuit given below, the current source is 1 A, voltage source is 5 V, R1 = R2 = R3 = 1 Ω, L1 = L2 = L3 = 1 H, C1 = C2 = 1 F. The current through R3 is _________

tough-network-theory-questions-answers-q6

a) 1 A
b) 5 A
c) 6 A
d) 8 A

6. In the circuit given below, the current source is 1 A, voltage source is 5 V, R1 = R2 = R3 = 1 Ω, L1 = L2 = L3 = 1 H, C1 = C2 = 1 F. The current through the voltage source V is _________

tough-network-theory-questions-answers-q6

a) 1 A
b) 3 A
c) 2 A
d) 4 A

7. In the circuit given below, the voltage across capacitor when switch is closed at t = ∞ is ____________

tough-network-theory-questions-answers-q5

a) 50 V
b) 20 V
c) 30 V
d) 7.5 V

8. In the circuit given below, the capacitor is initially having a charge of 10 C. 1 second after the switch is closed, the current in the circuit is ________

tough-network-theory-questions-answers-q7

a) 14.7 A
b) 18.5 A
c) 40.0 A
d) 50.0 A

9. In the circuit given below, the voltage across R by mesh analysis is _________

tough-network-theory-questions-answers-q9

a) 1.59 V
b) 1 V
c) 2.54 V
d) 1.54 V

10. A rectifier type AC voltmeter consists of a series resistance R, an ideal full-wave rectifier bridge and a PMMC instrument. The internal resistance and a full-scale deflection produced by a DC current are 100 Ω and 1 mA respectively. A voltage of 100 V (rms) is applied to the input terminals. The value of R required is _________
a) 63.56 Ω
b) 89.83 Ω
c) 89.83 kΩ
d) 141.3 kΩ

11. In the circuit given below, the switch is closed at t = 0. At t = 0+ the current through C is ___________

tough-network-theory-questions-answers-q5

a) 2 A
b) 3 A
c) 4 A
d) 5 A

12. In a dual slop integrating type digital voltmeter, the first integrating is carried out for 10 periods of the supply frequency of 50 Hz. If the reference voltage used is 2 V, the total conversion time for an input of 1 V is _________
a) 0.01 s
b) 0.05 s
c) 0.1 s
d) 1 s

13. A 1 μF capacitor is connected across a 50 V battery. The battery is kept closed for a long time. The circuit current and voltage across capacitor is __________
a) 0.5 A and 0 V
b) 0 A and 50 V
c) 20 A and 5 V
d) 0.05 A and 5 V

14. A digital Multimeter reads 10 V when fed with a triangular wave, which is symmetric about the time-axis. If the input is same, the rms reading meter will read?
a) 203√
b) –103√
c) –203√
d) 103√

15. A resistance R is measured using the connection shown in the below figure.

tough-network-theory-questions-answers-q15

The current measured is 10 A on ranges 100A and the voltage measured is 125 V on 150 V range. The scales of the ammeter and voltmeter are uniform. The total number of scale divisions of the ammeter is 100 and that of the voltmeter is 150. The scale division can be distinguished. The constructional error of the ammeter is ± 0.3% and that of voltmeter±0.4%. The resistance of the ammeter is 0.25 Ω. The value of R is _________
a) 12.75 Ω
b) 12.0 Ω
c) 12.25 Ω
d) 12.5 Ω

Leave a Reply

Your email address will not be published. Required fields are marked *